Universal CR-2149 - Safety Beam Sensors for Garage Door Openers | 
 enlarge | Brand: Digi-Code
Category: Home Improvement
Buy New: $31.99
New (7) from $31.99
Rating:  15 reviews
Sales Rank: 18018
Media: Misc.
Shipping Weight (lbs): 1.1
Dimensions (in): 7.1 x 4 x 2.8
MPN: CR2149
Model: CR2149
UPC: 753182405681
EAN: 0753182405681
ASIN: B0006OFYMO
Availability: Usually ships in 1-2 business days
| |
| Features:
| • | universal beam sensor works with all major brands of garage door openers such as - | | • | Chamberlain®, Liftmaster®, CraftsmanTM, and | | • | Overhead® (1995+), GenieTM, and | | • | Challenger®, Stanley®, Linear®, Moore-O-Matic® and Raynor® models ( built by Chamberlain® ). | | • | Self programming feature which allow the installer to simply hook up beams to the existing wiring. |
|
| Similar Items:
| |
| Editorial Reviews:
Product Description
The Universal Replacement Beam Sensor Kit includes:
One Sender and One Receiver Module
Two Mounting Brackets
Four Wood Screws
Instruction Sheet
|
| Customer Reviews:
Showing reviews 1-5 of 15
 DON"T EXPECT ANY TECH HELP!!! August 27, 2010
CRANKBAIT
I purchased these to replace a set of "yellow" sensors for a Moore-0-Matic opener...(14 years old)
The new ones only have 2 terminals, the old receiver has 4 terminals...There is of course no information in the instructions on how to wire these in this scenario...THERE IS ALSO OF COURSE NO, NONE, FORGET ABOUT IT, customer service or Tech support from Moore-O-Matic (now Linear Corp), Digi-Code or anyone else...PERIOD.
After much trial and error I finally got it to work....Matching all positive wires from the old to positive terminals of the new and the same with the negative wires and terminals (now here's the tricky part) reverse, YES, switch, the location of of the emitter and receiver to the opposite sides of the door!!! WHACKY??? YES!! But it works!!
I would never buy anything again from Linear Corp...Period.
Instructions next to useless and tech support doesn't exist June 10, 2010
Mister Grumpy (Springfield, Illinois USA)
I purchased this device for a Moore-o-matic Opener whose manufacturer had gone out of business. Although the instructions says that it is a simple snip of a wire on the back of the receiver....... it's not that simple..... the instructions do not explain how hook up a two wire device on a system with four connections (three wires). I did get the device to function, however I don't think the average person without some electrical knowledge will be able to get these to work. Plus, although my garage door open and closes as it should...... the sensors don't detect any blockages as the sensor system was designed to do...... but the opener works and that's all I care about....... If these devices fail, I won't be buying another.
In addition........ the technical support from the device manufacturer is nonexistent...... you wait on the phone for 15 minutes, and then you're sent to a voice mailbox to leave a message....... so don't waste your time calling.
 Solved my door closing problems. March 14, 2010
Medengineer (Goleta, CA United States)
My old beams on my Moore 'O Matic door opener began to have a lot of problems and the door would not close properly. These were a snap to install and solved my problem.
Excellent product September 12, 2009
Thomas Miller
1 out of 1 found this review helpful
Worked right out of the box. I was concerned because my garage door opener was about 15 years old, but these replacement sensors worked perfectly. The instructions were excellent, it explained which wire I had to snip, attached it to the existing wires, and bam, it was operational. Highly recommend.
Garage door sensors August 11, 2009
Gerald C. Maisonneuve (valley center, ca)
1 out of 1 found this review helpful
Sensor unit(s) arrived in excellent shape with great instructions. Easily installed and have worked perfectly...planning to order another set.
Showing reviews 1-5 of 15
|
|
|
